Replace direct !reset_n async sense with a registered active-high reset_h
(max_fanout=50) in nco_400m_enhanced, cic_decimator_4x_enhanced, and
ddc_400m. The prior single-LUT1 / 700+ load net was the root cause of
WNS=-0.626 ns in the 400 MHz clock domain on the xc7a50t build. Vivado
replicates the constrained register into ≈14 regional copies, each driving
≤50 loads, closing timing at 2.5 ns.
Change radar_system_top default USB_MODE from 0 (FT601) to 1 (FT2232H).
FT601 remains available for the 200T premium board via explicit parameter
override; the 50T production wrapper already hard-codes USB_MODE=1.
Regression: add usb_data_interface_ft2232h.v to PROD_RTL lint list and
both system-top TB compile commands; fix legacy radar_system_tb hierarchical
probe from gen_ft601.usb_inst to gen_ft2232h.usb_inst.
Golden reference files (rtl_bb_dc.csv, rx_final_doppler_out.csv,
golden_doppler.mem) regenerated to reflect the +1-cycle registered-reset
boundary behaviour; Receiver golden-compare passes 18/18 checks.
All 25 regression tests pass (0 failures, 0 skipped).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Regenerate all real-data golden reference hex files against the current
dual 16-point FFT Doppler architecture (staggered-PRI sub-frames).
The old hex files were generated against the previous 32-point single-FFT
architecture and caused 2048/2048 mismatches in both strict real-data TBs.
Changes:
- Regenerate doppler_ref_i/q.hex, fullchain_doppler_ref_i/q.hex, and all
downstream golden files (MTI, DC notch, CFAR) via golden_reference.py
- Add tb_doppler_realdata (exact-match, ADI CN0566 data) to regression
- Add tb_fullchain_realdata (exact-match, decim->Doppler chain) to regression
- Both TBs now pass: 2048/2048 bins exact match, MAX_ERROR=0
- Update CI comment: 23 -> 25 testbenches
- Fill in STALE_NOTICE.md with regeneration instructions
Regression: 25/25 pass, 0 fail, 0 skip. ruff check: 0 errors.
- Remove xfft_32.v, tb_xfft_32.v, and fft_twiddle_32.mem (dead code
since PR #33 moved Doppler to dual 16-pt FFT architecture)
- Update run_regression.sh: xfft_16 in PROD_RTL, remove xfft_32 from
EXTRA_RTL and all compile commands
- Update tb_fft_engine.v to test with N=16 / fft_twiddle_16.mem
- Update validate_mem_files.py: validate fft_twiddle_16.mem instead of 32
- Update testbenches and golden data from main_cleanup branch to match
dual-16 architecture (tb_doppler_cosim, tb_doppler_realdata,
tb_fullchain_realdata, tb_fullchain_mti_cfar_realdata, tb_system_e2e,
radar_receiver_final, golden_doppler.mem)
- Update CONTRIBUTING.md with full regression test instructions covering
FPGA, MCU, GUI, co-simulation, and formal verification
Regression: 23/23 FPGA, 20/20 MCU, 57/58 GUI, 56/56 mem validation,
all co-sim scenarios PASS.
- usb_data_interface.v: Add 3 self-test status inputs, expand status packet
from 7 words (header + 5 data + footer) to 8 words (header + 6 data + footer).
New status_words[5] carries {busy, detail[7:0], flags[4:0]}.
- radar_system_top.v: Wire self_test_flags_latched, self_test_detail_latched,
self_test_busy to usb_data_interface ports. Add opcode 0x31 as status
readback alias so host can read self-test results.
- tb_usb_data_interface.v: Add self-test port connections, verify word 5 in
Group 16, add Group 18 (busy flag + partial failure variant). 81 checks pass.
- run_regression.sh: Add fpga_self_test.v to PROD_RTL lint list and system-
level compile lists. Add tb_fpga_self_test as Phase 1 unit test.
- 24/24 regression tests pass, lint clean (0 errors, 4 advisory warnings).
MTI canceller (2-pulse, H(z)=1-z^{-1}) between range decimator and
Doppler processor. Subtracts previous chirp from current, nulling DC
Doppler (stationary clutter). Pass-through when host_mti_enable=0.
DC notch filter (post-Doppler, pre-CFAR) zeros bins within
+/-host_dc_notch_width of DC. Complements MTI for residual clutter.
New host registers: 0x26 (mti_enable), 0x27 (dc_notch_width).
Both default to 0 (disabled) - fully backward-compatible.
Verification: 23/23 regression, 29/29 MTI standalone, 3/3 real-data
co-sim (5137/5137 exact match) all PASS.
RTL fixes discovered via new end-to-end testbench:
- plfm_chirp_controller: TX/RX mixer enables now mutually exclusive
by FSM state (Fix#4), preventing simultaneous TX+RX activation
- usb_data_interface: stream control reset default 3'b001 (range-only),
added doppler/cfar data_pending sticky flags, write FSM triggers on
range_valid only — eliminates startup deadlock (Fix#5)
- radar_receiver_final: STM32 toggle signals wired through for mode-00
pass-through, dynamic frame detection via host_chirps_per_elev
- radar_system_top: STM32 toggle signal wiring to receiver instance
- chirp_memory_loader_param: explicit readmemh range for short chirp
Test infrastructure:
- New tb_system_e2e.v: 46 checks across 12 groups (reset, TX, safety,
RX, USB R/W, CDC, beam scanning, reset recovery, stream control,
latency budgets, watchdog)
- tb_usb_data_interface: Tests 21/22/56 updated for data_pending
architecture (preload flags, verify consumption instead of state)
- tb_chirp_controller: mixer tests T7.1/T7.2 updated for Fix#4
- run_regression.sh: PASS/FAIL regex fixed to match only [PASS]/[FAIL]
markers, added E2E test entry
- Updated rx_final_doppler_out.csv golden data
Adds two-layer lint pass (iverilog -Wall + custom static checks) that
catches part-select OOB errors and case-without-default warnings before
pushing to remote Vivado. Catches the exact Synth 8-524 class error that
broke Build 18 initial attempt. Lint errors abort regression; warnings
are advisory. Regenerated golden data for BRAM-migrated matched filter.
Jason