- Correct carrier from 10.525/10 GHz to 10.5 GHz (verified ADF4382 config)
- Correct range-per-bin from 4.8/5.6/781.25 m to 24.0 m (matched-filter)
- Correct velocity resolution from 1.484 to 2.67 m/s/bin (PRI-based)
- Correct processing rate from 4 MSPS to 100 MSPS (post-DDC)
- Correct max range from 307/5000/50000 m to 1536 m (64 bins x 24 m)
- Add WaveformConfig.pri_s field (167 us PRI for velocity calculation)
- Fix short chirp chirp_complete deadlock (Bug A)
- Remove dead short_chirp ports, rename long_chirp to ref_chirp (Bug B)
- Fix stale latency comment 2159 -> 3187 cycles (Bug C)
- Create radar_params.vh as single source of truth for FPGA parameters
- Lower RadarSettings.cpp map_size validation bound from 1000 to 100
- Add PLFM hardware constants to golden_reference.py
- Update all GUI versions, tests, and cross-layer contracts
All 244 tests passing (167 Python + 21 MCU + 29 cross-layer + 27 FPGA)
- Remove xfft_32.v, tb_xfft_32.v, and fft_twiddle_32.mem (dead code
since PR #33 moved Doppler to dual 16-pt FFT architecture)
- Update run_regression.sh: xfft_16 in PROD_RTL, remove xfft_32 from
EXTRA_RTL and all compile commands
- Update tb_fft_engine.v to test with N=16 / fft_twiddle_16.mem
- Update validate_mem_files.py: validate fft_twiddle_16.mem instead of 32
- Update testbenches and golden data from main_cleanup branch to match
dual-16 architecture (tb_doppler_cosim, tb_doppler_realdata,
tb_fullchain_realdata, tb_fullchain_mti_cfar_realdata, tb_system_e2e,
radar_receiver_final, golden_doppler.mem)
- Update CONTRIBUTING.md with full regression test instructions covering
FPGA, MCU, GUI, co-simulation, and formal verification
Regression: 23/23 FPGA, 20/20 MCU, 57/58 GUI, 56/56 mem validation,
all co-sim scenarios PASS.
MTI canceller (2-pulse, H(z)=1-z^{-1}) between range decimator and
Doppler processor. Subtracts previous chirp from current, nulling DC
Doppler (stationary clutter). Pass-through when host_mti_enable=0.
DC notch filter (post-Doppler, pre-CFAR) zeros bins within
+/-host_dc_notch_width of DC. Complements MTI for residual clutter.
New host registers: 0x26 (mti_enable), 0x27 (dc_notch_width).
Both default to 0 (disabled) - fully backward-compatible.
Verification: 23/23 regression, 29/29 MTI standalone, 3/3 real-data
co-sim (5137/5137 exact match) all PASS.
RTL fixes discovered via new end-to-end testbench:
- plfm_chirp_controller: TX/RX mixer enables now mutually exclusive
by FSM state (Fix#4), preventing simultaneous TX+RX activation
- usb_data_interface: stream control reset default 3'b001 (range-only),
added doppler/cfar data_pending sticky flags, write FSM triggers on
range_valid only — eliminates startup deadlock (Fix#5)
- radar_receiver_final: STM32 toggle signals wired through for mode-00
pass-through, dynamic frame detection via host_chirps_per_elev
- radar_system_top: STM32 toggle signal wiring to receiver instance
- chirp_memory_loader_param: explicit readmemh range for short chirp
Test infrastructure:
- New tb_system_e2e.v: 46 checks across 12 groups (reset, TX, safety,
RX, USB R/W, CDC, beam scanning, reset recovery, stream control,
latency budgets, watchdog)
- tb_usb_data_interface: Tests 21/22/56 updated for data_pending
architecture (preload flags, verify consumption instead of state)
- tb_chirp_controller: mixer tests T7.1/T7.2 updated for Fix#4
- run_regression.sh: PASS/FAIL regex fixed to match only [PASS]/[FAIL]
markers, added E2E test entry
- Updated rx_final_doppler_out.csv golden data
P0-1: nco_400m_enhanced.v — DSP48E1 OPMODE corrected from PCIN to P
feedback (was routing stale cascade data into accumulator)
P0-2: radar_receiver_final.v — removed same-clock CDC that corrupted
ADC data path between ad9484_interface and DDC
P1-5: fir_lowpass.v — fixed zero replication count in coefficient
symmetric extension ({0{1'b0}} is empty, now uses explicit 0)
Also updates .gitignore to exclude debug/scratch artifacts.
All 30+ testbenches pass (unit, co-sim, integration).
RTL fix: matched_filter_multi_segment.v ST_WAIT_FFT now waits for
processing chain to complete ALL 1024 outputs and return to IDLE
before advancing to next segment. Previously, it transitioned on the
first fft_pc_valid edge, causing the chain to still be outputting
while multi-seg started collecting data for the next segment. This
broke the handshake and caused permanent deadlock after segment 0.
Also fixes forward reference of sample_addr_from_chain in
radar_receiver_final.v (declaration moved before first use).
New files:
- tb/tb_radar_receiver_final.v: P0 integration test for full RX
pipeline (ADC->DDC->MF->range_bin_decimator->doppler), 10 checks
- tb/ad9484_interface_400m_stub.v: behavioral ADC stub for iverilog
All existing tests still pass: multi-seg 32/32, MF co-sim 3/3,
Doppler co-sim 14/14.
Jason
NawfalMotii79